Preparation and Corrosion Resistance of Thermally Cured EP-PVC Composite Powder Coatings
Main Article Content
Abstract
Marine metal structures such as ships and submarines are exposed to highly corrosive environments, requiring coatings that provide durable protection while maintaining environmental safety. This study investigates thermally cured EP-PVC composite powder coatings prepared via electrostatic spraying, comparing layer-by-layer and co-curing processes. The EP-PVC primer layer and PVC topcoat were analyzed using FT-IR, Raman spectroscopy, and TEM to understand microstructural evolution. Mechanical tests, including hardness, gloss, adhesion, and impact resistance, along with salt spray and potentiodynamic polarization tests, demonstrated that layer-by-layer cured coatings exhibit superior adhesion, hardness, and corrosion resistance, with corrosion rates as low as 0.0018 mm/a and overall protection reaching 67%. The enhanced barrier properties and interfacial bonding of the composite coatings effectively inhibit corrosive media penetration. These coatings are particularly suitable for electromagnetic engineering applications, such as protective surfaces for antenna arrays, RF transmission structures, and high-frequency marine electronics, where durable corrosion resistance is critical for long-term signal integrity and system reliability.
Downloads
Article Details
This work is licensed under a Creative Commons Attribution 4.0 International License.
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
References
C. Googan, “Marine Corrosion and Cathodic Protection,” Corrosion Management, 2022, doi: 10.1201/9781003216070.
N. H. Othman, C. Ismail, M. Mustapha, et al., “Graphene-based polymer nanocomposites as barrier coatings for corrosion protection,” Progress in Organic Coatings, vol. 135, pp. 82–99, 2019, doi: 10.1016/j.porgcoat.2019.05.030.
H. Alhumade, A. Abdala, A. Yu, et al., “Corrosion inhibition of copper in sodium chloride solution using polyetherimide/graphene composites,” The Canadian Journal of Chemical Engineering, vol. 94, no. 5, pp. 896– 904, 2016, doi: 10.1002/cjce.22439.
W. Wang, Y. Wang, Z. Liu, et al., “Study on application performance of oxidized polyethylene wax in powder coatings,” Progress in Organic Coatings, vol. 136, Art. no. 105294, 2019, doi: 10.1016/j.porgcoat.2019.105294.
X. Yu, Q. Wu, and R. W. J. Chen, “PREPARATION AND CORROSION RESISTACE OF EPOXY RESIN COATING WITH DOPAMINE MODIFIED BASALT FIBER,” Digest Journal of Nanomaterials and Biostructures, vol. 15, no. 4, pp. 1117–1127, 2020, doi: 10.15251/djnb.2020.154.1117.
Y. Wu, Y. He, C. Chen, et al., “MoS2-CNFs composites to enhance the anticorrosive and mechanical performance of epoxy coating,” Progress in Organic Coatings, vol. 129, pp. 178–186, 2019, doi: 10.1016/j.porgcoat.2019.01.021.
R. Ding, S. Chen, J. Lv, et al., “Study on graphene modified organic anti-corrosion coatings: A comprehensive review,” Journal of Alloys and Compounds, vol. 806, pp. 611–635, 2019, doi: 10.1016/j.jallcom.2019.07.256.
L. Cheng, C. Liu, D. Han, et al., “Effect of graphene on corrosion resistance of waterborne inorganic zinc-rich coatings,” Journal of Alloys and Compounds, vol. 774, pp. 255–264, 2018, doi: 10.1016/j.jallcom.2018.09.315.
X. N. Shen, M. Z. Ji, S. M. Zhang, et al., “Fabrication of multi-walled carbon-nanotube-grafted polyvinyl-chloride composites with high solar-thermal-conversion performance,” Composites Science and Technology, vol. 170, pp. 77–84, 2019, doi: 10.1016/j.compscitech.2018.11.029.
K. Wang, “Effect of Holding Temperature on Wear and Corrosion Resistance of Rare Earth Oxide Thermally Diffused Zinc Coatings,” Coatings, vol. 15, 2025, doi: 10.3390/coatings15030290.
Y. Kang, X. Chen, S. Song, et al., “Friction and wear behavior of nanosilica-filled epoxy resin composite coatings,” Applied Surface Science, vol. 258, no. 17, pp. 6384–6390, 2012, doi: 10.1016/j.apsusc.2012.03.046.
M. G. Sari, M. Shamshiri, and B. Ramezanzadeh, “Fabricating an epoxy composite coating with enhanced corrosion resistance through impregnation of functionalized graphene oxide-co-montmorillonite Nanoplatelet,” Corrosion Science, vol. 129, pp. 38–53, 2017, doi: 10.1016/j.corsci.2017.09.024.
R. M. Bandeira, J. Van Drunen, D. S. F. F. Augusto, et al., “Chemically synthesized polyaniline/ polyvinyl chloride blended coatings for the corrosion protection of AA7075 aluminum alloy,” Corrosion Science, vol. 139, pp. 35–46, 2018, doi: 10.1016/j.corsci.2018.04.031.
S. Kuroda, J. Kawakita, and M. Takemoto, “An 18-year exposure test of thermal-sprayed Zn, Al, and Zn-Al coatings in marine environment,” Corrosion, vol. 62, pp. 635–647, 2006, doi: 10.5006/1.3280677.
H. B. Choe, H.-S. Lee, M. A. Ismail, et al., “Evaluation of Electrochemical Impedance Properties of Anti-corrosion Films by Arc Thermal Metal Spraying Method,” International Journal of Electrochemical Science, vol. 10, no. 11, pp. 9775–9789, 2015, doi: 10.1016/s1452-3981(23)11219-3.
F. Ahnia and B. Demri, “Evaluation of aluminum coatings in simulated marine environment,” Surface & Coatings Technology, vol. 220, pp. 232– 236, 2013, doi: 10.1016/j.surfcoat.2012.12.011.
F. Q. Zhang, H. C. Wang, L. T. Wang, et al., “Superhydrophobic carbon nanotubes/epoxy nanocomposite coating by facile one-step spraying,” Surface & Coatings Technology, vol. 341, 2018, doi: 10.1016/j.surfcoat.2018.01.045.
D. Li, X. Cui, C. Yuan, et al., “Effect of Ni modified graphene on microstructure and properties of Ni60 composite coatings prepared by laser cladding,” Optics & Laser Technology, vol. 136, no. 5, Art. no. 106756, 2020, doi: 10.1016/j.optlastec.2020.106756.
G. D. Sia, X. Y. Hong, and W. Y. M. Hung, “Preservable superhydrophilicity of thermally cured graphene-nanoplatelets/epoxy nanocomposite coatings,” Composites, Part B. Engineering, vol. 252, no. Mar.1, pp. 110500.1– 110500.15, 2023, doi: 10.1016/j.compositesb.2023.110500.
Y. Li, X. Zhang, Y. Cui, et al., “Anti-corrosion enhancement of superhydrophobic coating utilizing oxygen vacancy modified potassium titanate whisker,” Chemical Engineering Journal, vol. 374, pp. 1326–1336, 2019, doi: 10.1016/j.cej.2019.06.028.