Calculation of harmonic losses and ampacity in low-voltage power cables when used for feeding large LED lighting loads

Main Article Content

N. J. Milardovich
L. Prevosto
M. A. Lara

Abstract

A numerical investigation on the harmonic disturbances in low-voltage cables feeding large LED loads is reported. A frequency domain analysis on several commercially-available LEDs was performed to investigate the signature of the harmonic current injected into the power system. Four-core cables and four single-core cable arrangements (three phases and neutral) of small, medium, and large conductor cross sections, with the neutral conductor cross section approximately equal to the half of the phase conductors, were examined. The cables were modelled by using electromagnetic finite-element analysis software. High harmonic power losses (up to 2.5 times the value corresponding to an undistorted current of the same rms value of the first harmonic of the LED current) were found. A generalized ampacity model was employed for re-rating the cables. It was found that the cross section of the neutral conductor plays an important role in the derating of the cable ampacity due to the presence of a high-level of triplen harmonics in the distorted current. The ampacity of the cables should be derated by about 40 %, almost independent of the conductor cross sections. The calculation have shown that an incoming widespread use of LED lamps in lighting could create significant additional harmonic losses in the supplying low-voltage lines, and thus more severely harmonic emission limits should be defined for LED lamps.

Downloads

Download data is not yet available.

Article Details

How to Cite
Milardovich, N., Prevosto, L., & Lara, M. A. (2014). Calculation of harmonic losses and ampacity in low-voltage power cables when used for feeding large LED lighting loads. Advanced Electromagnetics, 3(1), 50-56. https://doi.org/10.7716/aem.v3i1.258
Section
Research Articles

References


  1. I. L. Azevedo, M. G. Morgan, F. Morgan, The transition to solid-state lighting, Proc. IEEE 97: 481-510, 2009.
    View Article

  2. S. Chong-Tan, General n-Level Driving Approach for Improving Electrical-to-Optical Energy-Conversion Efficiency of Fast-Response Saturable Lighting Devices, IEEE Trans. Ind. Electron. 57: 1342-1353, 2010.
    View Article

  3. W. Chen, S. Y. Ron Hui, Elimination of an Electrolytic Capacitor in AC/DC Light-Emitting Diode (LED) Driver With High Input Power Factor and Constant Output Current, IEEE Trans. Power Electron. 27: 1598-1607, 2012.
    View Article

  4. X. Qu, S. C. Wong, C. K. Tse, Resonance assisted buck converter for offline driving of power LED replacement lamps, IEEE Trans.Power Electron. 26: 532-540, 2011.
    View Article

  5. J. J. M. Desmet, I. Sweertvaegher, G. Vanalme, K. Stockman, R. J. M. Belmans, Analysis of the neutral conductor current in a three-phase supplied network with nonlinear single-phase loads, IEEE Trans. Ind. Appl. 39: 587–593, 2003.
    View Article

  6. A. P. S. Meliopoulos, M. A. Martin Jr., Calculation of Secondary Cable Losses and Ampacity in the Presence of Harmonics, IEEE Trans. Power Delivery 7: 451-459, 1992.
    View Article

  7. C. Demoulias, D. P. Labridis, P. S. Dokopoulos, K. Gouramanis, Ampacity of Low-Voltage Power Cables Under Nonsinusoidal Currents, IEEE Trans. Power Delivery 22: 584-594, 2007.
    View Article

  8. A. Hiranandani, Calculation of cable ampacities including the effects of harmonics, IEEE Trans. Industry Applicat.4: 42-51, 1998.

  9. S. Muthu, F.J. Schuunnans and M. Pashley, Red, green, and blue LEDs for white light illumination, IEEE J. Quantum Electron. 8: 333-338, 2002.
    View Article

  10. S. Uddin, H. Shareef; A. Mohamed; M. A. Hannan, An Analysis of Harmonic Diversity Factors Applied to LED Lamps, Proc. POWERCON12, Auckland, New Zealand, pp. 1-5, 2012.

  11. V. Cuk, J.F.G. Cobben, W.L. Kling, R.B. Timens, An Analysis of Diversity Factors applied to Harmonic Emission Limits for Energy Saving Lamps, ICHQP10, Bergamo, Italy, pp. 1-6, 2010.

  12. Cables for rated voltages of 1 kV, IEC 60502-1: 2004 (E).

  13. Distribution cables of rated voltage 0,6/1 kV, CENELEC Std. HD603 S1:1994/A2: 2003 E.

  14. QuickField Lite User Guide, Tera Analysis Ltd., 2014.

  15. International standard of resistance for copper, IEC 60028 Ed. 2.0 B: 1925. Electrical Installations of Buildings—Part 5: Selection and Election of Electrical Equipment—Section 523: Current-Carrying Capacities in Wiring Systems, CENELEC Std. HD384.5.523, 2001, S2. Iec 60287.

  16. Electric cables-Calculation of the current rating, IEC 60287-1-1, CEI/IEC 60287-1-1:2006.

  17. A. Hiranandani, Calculation of conductor temperatures and ampacities of cable systems using a generalized finite difference model, IEEE Power Delivery.6: 15-24, 1991.
    View Article

  18. J. H. Neher, M. H. McGrath, The Calculation of the Temperature Rise and Load Capability of Cable Systems, AIEE Transactions. 76: 752-772, 1957.

  19. Limits for harmonic current emissions (equipment input current ≤ 16A per phase), IEC 61000-3-2 Ed. 3.2 2009-04.